|
- # Hitex STR9-comStick
- # http://www.hitex.com/index.php?id=383
- # This works for the STR9-comStick revisions STR912CS-A1 and STR912CS-A2.
-
- source [find interface/hitex_str9-comstick.cfg]
-
- # set jtag speed
- adapter_khz 3000
-
- adapter_nsrst_delay 100
- jtag_ntrst_delay 100
- #use combined on interfaces or targets that can't set TRST/SRST separately
- reset_config trst_and_srst
-
- #
- # FIXME use the standard str912 target config; that script might need
- # updating to "-ignore-version" for the boundary scan TAP
- #
- # source [find target/str912.cfg]
- #
-
- if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
- } else {
- set _CHIPNAME str912
- }
-
- if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
- } else {
- set _ENDIAN little
- }
-
- if { [info exists FLASHTAPID] } {
- set _FLASHTAPID $FLASHTAPID
- } else {
- set _FLASHTAPID 0x04570041
- }
- jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
-
- if { [info exists CPUTAPID] } {
- set _CPUTAPID $CPUTAPID
- } else {
- set _CPUTAPID 0x25966041
- }
- jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
- if { [info exists BSTAPID] } {
- set _BSTAPID $BSTAPID
- } else {
- # Found on STR9-comStick, revision STR912CS-A1
- set _BSTAPID1 0x1457f041
- # Found on STR9-comStick, revision STR912CS-A2
- set _BSTAPID2 0x2457f041
- }
- jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID1 -expected-id $_BSTAPID2
-
- set _TARGETNAME $_CHIPNAME.cpu
- target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME
-
- $_TARGETNAME configure -event reset-init {
- # We can increase speed now that we know the target is halted.
- #jtag_rclk 3000
-
- # -- Enable 96K RAM
- # PFQBC enabled / DTCM & AHB wait-states disabled
- mww 0x5C002034 0x0191
-
- str9x flash_config 0 4 2 0 0x80000
- flash protect 0 0 7 off
- }
-
- $_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
-
- #flash bank <driver> <base> <size> <chip_width> <bus_width>
- set _FLASHNAME $_CHIPNAME.flash0
- flash bank $_FLASHNAME str9x 0x00000000 0x00080000 0 0 0
- set _FLASHNAME $_CHIPNAME.flash1
- flash bank $_FLASHNAME str9x 0x00080000 0x00008000 0 0 0
|