You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

142 lines
5.5 KiB

  1. ################################################################################
  2. # Olimex SAM9-L9260 Development Board
  3. #
  4. # http://www.olimex.com/dev/sam9-L9260.html
  5. #
  6. # Atmel AT91SAM9260 : PLLA = 198.656 MHz, MCK = 99.328 MHz
  7. # PMC configured for external 18.432 MHz crystal
  8. #
  9. # 32-bit SDRAM : 2 x Samsung K4S561632J-UC75, 4M x 16Bit x 4 Banks
  10. # 8-bit NAND Flash : 1 x Samsung K9F4G08U0M, 512M x 8Bit
  11. # Dataflash : 1 x Atmel AT45DB161D, 16Mbit
  12. #
  13. ################################################################################
  14. source [find target/at91sam9260.cfg]
  15. # NTRST_E jumper is enabled by default, so we don't need to override the reset
  16. # config.
  17. #reset_config srst_only
  18. $_TARGETNAME configure -event reset-start {
  19. # At reset, CPU runs at 32.768 kHz. JTAG frequency must be 6 times slower if
  20. # RCLK is not supported.
  21. jtag_rclk 5
  22. halt
  23. # RSTC_MR : enable user reset, reset length is 64 slow clock cycles. MMU may
  24. # be enabled... use physical address.
  25. mww phys 0xfffffd08 0xa5000501
  26. }
  27. $_TARGETNAME configure -event reset-init {
  28. mww 0xfffffd44 0x00008000 ;# WDT_MR : disable watchdog
  29. ##
  30. # Clock configuration for 99.328 MHz main clock.
  31. ##
  32. echo "Setting up clock"
  33. mww 0xfffffc20 0x00004001 ;# CKGR_MOR : enable main oscillator, 512 slow clock startup
  34. sleep 20 ;# wait 20 ms (need 15.6 ms for startup)
  35. mww 0xfffffc30 0x00000001 ;# PMC_MCKR : switch to main oscillator (18.432 MHz)
  36. sleep 10 ;# wait 10 ms
  37. mww 0xfffffc28 0x2060bf09 ;# CKGR_PLLAR : 18.432 MHz / 9 * 97 = 198.656 MHz, 63 slow clock startup
  38. sleep 20 ;# wait 20 ms (need 1.9 ms for startup)
  39. mww 0xfffffc30 0x00000101 ;# PMC_MCKR : no scale on proc clock, master is proc / 2
  40. sleep 10 ;# wait 10 ms
  41. mww 0xfffffc30 0x00000102 ;# PMC_MCKR : switch to PLLA (99.328 MHz)
  42. # Increase JTAG speed to 6 MHz if RCLK is not supported.
  43. jtag_rclk 6000
  44. arm7_9 dcc_downloads enable ;# Enable faster DCC downloads.
  45. ##
  46. # SDRAM configuration for 2 x Samsung K4S561632J-UC75, 4M x 16Bit x 4 Banks.
  47. ##
  48. echo "Configuring SDRAM"
  49. mww 0xfffff870 0xffff0000 ;# PIOC_ASR : select peripheral function for D15..D31
  50. mww 0xfffff804 0xffff0000 ;# PIOC_PDR : disable PIO function for D15..D31
  51. mww 0xffffef1c 0x00010002 ;# EBI_CSA : assign EBI CS1 to SDRAM, VDDIOMSEL set for +3V3 memory
  52. mww 0xffffea08 0x85237259 ;# SDRAMC_CR : configure SDRAM for Samsung chips
  53. mww 0xffffea00 0x1 ;# SDRAMC_MR : issue NOP command
  54. mww 0x20000000 0
  55. mww 0xffffea00 0x2 ;# SDRAMC_MR : issue an 'All Banks Precharge' command
  56. mww 0x20000000 0
  57. mww 0xffffea00 0x4 ;# SDRAMC_MR : issue 8 x 'Auto-Refresh' command
  58. mww 0x20000000 0
  59. mww 0xffffea00 0x4
  60. mww 0x20000000 0
  61. mww 0xffffea00 0x4
  62. mww 0x20000000 0
  63. mww 0xffffea00 0x4
  64. mww 0x20000000 0
  65. mww 0xffffea00 0x4
  66. mww 0x20000000 0
  67. mww 0xffffea00 0x4
  68. mww 0x20000000 0
  69. mww 0xffffea00 0x4
  70. mww 0x20000000 0
  71. mww 0xffffea00 0x4
  72. mww 0x20000000 0
  73. mww 0xffffea00 0x3 ;# SDRAMC_MR : issue a 'Load Mode Register' command
  74. mww 0x20000000 0
  75. mww 0xffffea00 0x0 ;# SDRAMC_MR : normal mode
  76. mww 0x20000000 0
  77. mww 0xffffea04 0x2b6 ;# SDRAMC_TR : set refresh timer count to 7 us
  78. ##
  79. # NAND Flash Configuration for 1 x Samsung K9F4G08U0M, 512M x 8Bit.
  80. ##
  81. echo "Configuring NAND flash"
  82. mww 0xfffffc10 0x00000010 ;# PMC_PCER : enable PIOC clock
  83. mww 0xfffff800 0x00006000 ;# PIOC_PER : enable PIO function for 13(RDY/~BSY) and 14(~CS)
  84. mww 0xfffff810 0x00004000 ;# PIOC_OER : enable output on 14
  85. mww 0xfffff814 0x00002000 ;# PIOC_ODR : disable output on 13
  86. mww 0xfffff830 0x00004000 ;# PIOC_SODR : set 14 to disable NAND
  87. mww 0xfffff864 0x00002000 ;# PIOC_PUER : enable pull-up on 13
  88. mww 0xffffef1c 0x0001000A ;# EBI_CSA : assign EBI CS3 to NAND, same settings as before
  89. mww 0xffffec30 0x00010001 ;# SMC_SETUP3 : 1 clock cycle setup for NRD and NWE
  90. mww 0xffffec34 0x03030303 ;# SMC_PULSE3 : 3 clock cycle pulse for all signals
  91. mww 0xffffec38 0x00050005 ;# SMC_CYCLE3 : 5 clock cycle NRD and NWE cycle
  92. mww 0xffffec3C 0x00020003 ;# SMC_MODE3 : NRD and NWE control, no NWAIT, 8-bit DBW,
  93. # 3 TDF cycles, no optimization
  94. mww 0xffffe800 0x00000001 ;# ECC_CR : reset the ECC parity registers
  95. mww 0xffffe804 0x00000002 ;# ECC_MR : page size is 2112 words (word is 8 bits)
  96. nand probe at91sam9260.flash
  97. ##
  98. # Dataflash configuration for 1 x Atmel AT45DB161D, 16Mbit
  99. ##
  100. echo "Setting up dataflash"
  101. mww 0xfffff404 0x00000807 ;# PIOA_PDR : disable PIO function for 0(SPI0_MISO), 1(SPI0_MOSI),
  102. # 2(SPI0_SPCK), and 11(SPI0_NPCS1)
  103. mww 0xfffff470 0x00000007 ;# PIOA_ASR : select peripheral A function for 0, 1, and 2
  104. mww 0xfffff474 0x00000800 ;# PIOA_BSR : select peripheral B function for 11
  105. mww 0xfffffc10 0x00001000 ;# PMC_PCER : enable SPI0 clock
  106. mww 0xfffc8000 0x00000080 ;# SPI0_CR : software reset SPI0
  107. mww 0xfffc8000 0x00000080 ;# SPI0_CR : again to be sure
  108. mww 0xfffc8004 0x000F0011 ;# SPI0_MR : master mode with nothing selected
  109. mww 0xfffc8034 0x011a0302 ;# SPI0_CSR1 : capture on leading edge, 8-bits/tx. 33MHz baud,
  110. # 250ns delay before SPCK, 250ns b/n tx
  111. mww 0xfffc8004 0x000D0011 ;# SPI0_MR : same config, select NPCS1
  112. mww 0xfffc8000 0x00000001 ;# SPI0_CR : enable SPI0
  113. }
  114. nand device at91sam9260.flash at91sam9 at91sam9260.cpu 0x40000000 0xffffe800
  115. at91sam9 cle 0 22
  116. at91sam9 ale 0 21
  117. at91sam9 rdy_busy 0 0xfffff800 13
  118. at91sam9 ce 0 0xfffff800 14