|
- #
- # Texas Instruments DaVinci family: TMS320DM365
- #
- if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
- } else {
- set _CHIPNAME dm365
- }
-
- # TI boards default to EMU0/EMU1 *high* -- ARM and ETB are *disabled*
- # after JTAG reset until ICEpick is used to route them in.
- set EMU01 "-disable"
-
- # With EMU0/EMU1 jumpered *low* ARM and ETB are *enabled* without
- # needing any ICEpick interaction.
- #set EMU01 "-enable"
-
- source [find target/icepick.cfg]
-
- # Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
- if { [info exists ETB_TAPID ] } {
- set _ETB_TAPID $ETB_TAPID
- } else {
- set _ETB_TAPID 0x2b900f0f
- }
- jtag newtap $_CHIPNAME etb -irlen 4 -irmask 0xf -expected-id $_ETB_TAPID $EMU01
- jtag configure $_CHIPNAME.etb -event tap-enable \
- "icepick_c_tapenable $_CHIPNAME.jrc 1"
-
- # Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
- if { [info exists CPU_TAPID ] } {
- set _CPU_TAPID $CPU_TAPID
- } else {
- set _CPU_TAPID 0x0792602f
- }
- jtag newtap $_CHIPNAME arm -irlen 4 -irmask 0xf -expected-id $_CPU_TAPID $EMU01
- jtag configure $_CHIPNAME.arm -event tap-enable \
- "icepick_c_tapenable $_CHIPNAME.jrc 0"
-
- # Primary TAP: ICEpick (JTAG route controller) and boundary scan
- if { [info exists JRC_TAPID ] } {
- set _JRC_TAPID $JRC_TAPID
- } else {
- set _JRC_TAPID 0x0b83e02f
- }
- jtag newtap $_CHIPNAME jrc -irlen 6 -irmask 0x3f -expected-id $_JRC_TAPID
-
- jtag configure $_CHIPNAME.jrc -event setup \
- "jtag tapenable $_CHIPNAME.etb; jtag tapenable $_CHIPNAME.arm"
-
- ################
-
- # various symbol definitions, to avoid hard-wiring addresses
- # and enable some sharing of DaVinci-family utility code
- global dm365
- set dm365 [ dict create ]
-
- # Physical addresses for controllers and memory
- # (Some of these are valid for many DaVinci family chips)
- dict set dm365 sram0 0x00010000
- dict set dm365 sram1 0x00014000
- dict set dm365 sysbase 0x01c40000
- dict set dm365 pllc1 0x01c40800
- dict set dm365 pllc2 0x01c40c00
- dict set dm365 psc 0x01c41000
- dict set dm365 gpio 0x01c67000
- dict set dm365 a_emif 0x01d10000
- dict set dm365 a_emif_cs0 0x02000000
- dict set dm365 a_emif_cs1 0x04000000
- dict set dm365 ddr_emif 0x20000000
- dict set dm365 ddr 0x80000000
-
- source [find target/davinci.cfg]
-
- ################
- # GDB target: the ARM, using SRAM1 for scratch. SRAM0 (also 16K)
- # and the ETB memory (4K) are other options, while trace is unused.
- set _TARGETNAME $_CHIPNAME.arm
-
- target create $_TARGETNAME arm926ejs -chain-position $_TARGETNAME
-
- # NOTE that work-area-virt presumes a Linux 2.6.30-rc2+ kernel,
- # and that the work area is used only with a kernel mmu context ...
- $_TARGETNAME configure \
- -work-area-virt [expr 0xfffe0000 + 0x4000] \
- -work-area-phys [dict get $dm365 sram1] \
- -work-area-size 0x4000 \
- -work-area-backup 0
-
- # be absolutely certain the JTAG clock will work with the worst-case
- # CLKIN = 19.2 MHz (best case: 36 MHz) even when no bootloader turns
- # on the PLL and starts using it. OK to speed up after clock setup.
- jtag_rclk 1500
- $_TARGETNAME configure -event "reset-start" { jtag_rclk 1500 }
-
- arm7_9 fast_memory_access enable
- arm7_9 dcc_downloads enable
-
- # trace setup
- etm config $_TARGETNAME 16 normal full etb
- etb config $_TARGETNAME $_CHIPNAME.etb
|