Signed-off-by: Paul Fertser <fercerpav@gmail.com>jim-nuttx
@@ -2,149 +2,27 @@ This file includes highlights of the changes made in the OpenOCD | |||
source archive release. | |||
JTAG Layer: | |||
* New driver for J-Link adapters based on libjaylink | |||
(including support for FPGA configuration, SWO and EMUCOM) | |||
* FTDI improvements to work at 30MHz clock | |||
* BCM2835 native driver SWD and Raspberry Pi2 support | |||
* BCM2835 is set to 4ma drive, slow slew rate | |||
* ixo-usb-jtag (emulation of an Altera Bus Blaster I on | |||
Cypress FX2 IC) support | |||
* JTAG pass-through mode for CMSIS-DAP (including support for | |||
FPGA configuration) | |||
* OpenJTAG support for Cypress CY7C65215 | |||
* connect_assert_srst support for SWD | |||
* Xilinx Virtex-II Series7 bitstream loading support | |||
* Use JEP106 data to decode IDs | |||
* Deprecated "ft2232" driver removed (use "ftdi" instead) | |||
* GPL-incompatible FTDI D2XX library support dropped (Presto, | |||
OpenJTAG and USB-Blaster I are using libftdi only now) | |||
* ZY1000 support dropped (unmaintained since long) | |||
* oocd_trace support dropped | |||
Boundary Scan: | |||
Target Layer: | |||
* ARMv7-A, Cortex-M, Cortex-A/R important fixes and | |||
improvements (allowing e.g. simultaneous debugging of A8 and | |||
M3 cores, JTAG WAIT support etc.) | |||
* ARM Cortex-A,R allow interrupt disable during single-step | |||
(maskisr command) | |||
* Semihosting support for ARMv7-A | |||
* ARM Cortex-M7 support | |||
* Intel Quark mcu D2000 support | |||
* Freescale LS102x SAP support | |||
* ThreadX RTOS support on ARM926E-JS | |||
* Cortex-M RTOS stack alignment fixes | |||
* FreeRTOS FPU support | |||
* uC/OS-III RTOS support | |||
* bridging semihosting to GDB's File-I/O support | |||
* -defer-examine option added to target create command | |||
* verify_image_checksum command added | |||
Flash Layer: | |||
* Atmel SAM4S, SAM4N, SAM4C support | |||
* Atmel SAMV, SAMS, SAME (Cortex-M7) support | |||
* Atmel AT91SAMD handle reset run/halt in DSU, other fixes | |||
* Atmel AT91SAML21, SAML22, SAMC20/SAMC21, SAMD09 support | |||
* ST STM32F4x support | |||
* ST STM32F74x/76x/77x, STM32L4 support | |||
* ST STM32L0 categories 1, 2 and 5 support | |||
* Kinetis K02, K21, K22, K24, K26, K63, K64, K66 support | |||
* Kinetis KE, KVx, K8x families support | |||
* Kinetis FlexNVM handling | |||
* Kinetis flash protection, security, mass_erase improvements | |||
* Infineon XMC4xxx family support | |||
* Infineon XMC1000 flash driver | |||
* Energy Micro EFM32 Happy Gecko support | |||
* Energy Micro EFM32 debug interface lock support | |||
* Analog Devices ADuCM360 support | |||
* Unified Nuvoton NuMicro flash driver | |||
* NIIET K1921VK01T (Cortex-M4) support | |||
* Nordic Semiconductor nRF51 improvements | |||
* Spansion FM4 flash (including MB9BFx64/x65, S6E2DH) driver | |||
* Ambiq Micro Apollo flash driver | |||
* PIC32MX new device IDs, 17x/27x flash support | |||
* read_bank() and verify_bank() NOR flash internal API to | |||
allow reading (and verifying) non-memory-mapped devices | |||
* JTAGSPI driver to access SPI NOR flashes via a trivial | |||
FPGA proxy | |||
* Milandr read/verify for Info memory support | |||
* Various discrete SPI NOR flashes support | |||
* CFI 16-bit flash reversed endianness support | |||
Board, Target, and Interface Configuration Scripts: | |||
* Digilent JTAG-HS2, JTAG-HS3 interfaces configs | |||
* FTDI UM232H module as JTAG interface config | |||
* 100ask's OpenJTAG interface config | |||
* MBFTDI interface config | |||
* XDS100v3 interface config | |||
* Freescale Vybrid VF6xx target config | |||
* EmCraft VF6 SOM and baseboard configs | |||
* Freescale SabreSD board config | |||
* Freescale VF65GS10 tower board config | |||
* Pipistrello Xilinx Spartan6 LX45 FPGA board config | |||
* miniSpartan6+ board config | |||
* Xilinx Kintex7 Development board config | |||
* Parallella-I board config | |||
* Digilent Atlys and Analog Discovery board configs | |||
* Numato Opsis board config | |||
* Xilinx Spartan 6 FPGA "Device DNA" reading support | |||
* Altera 10M50 FPGA (MAX10 family) target config | |||
* Altera EPM240 CPLD (MAXII family) target config | |||
* Marsohod2, Marsohod3 FPGA, Marsohod CPLD boards configs | |||
* Novena's integrated FPGA board config | |||
* XMOS XS1-XAU8A-10's ARM core config | |||
* XMOS xCORE-XA Core Module board config | |||
* Exynos5250 target config | |||
* Arndale board config | |||
* FM4 MB9BFxxx family configs | |||
* Spansion SK-FM4-U120-9B560 board config | |||
* Diolan LPC4357-DB1 board config | |||
* ST STM32F469 discovery board config | |||
* ST STM32F7-DISCO, STM327[4|5]6G-EVAL boards configs | |||
* ST STM32L4 discovery, NUCLEO L476RG, STM32F429I-DISC1 boards | |||
configs | |||
* Atheros AR2313, AR2315 targets config | |||
* Netgear WP102 board config | |||
* La Fonera FON2200 board config | |||
* Linksys WAG200G board config | |||
* LPC-Link2 board config | |||
* NXP LPC4370 target config | |||
* Atmel SAMV, SAMS, SAME target configs | |||
* Atmel SAM E70 Xplained, SAM V71 Xplained Ultra boards | |||
configs | |||
* Nordic nRF52 target config | |||
* Nordic nRF51-DK, nRF52-DK boards configs | |||
* Infineon XMC4700 Relax Kit, XMC4800 Relax EtherCAT Kit, | |||
XMC4300 Relax EtherCAT Kit boards configs | |||
* Renesas S7G2 target config | |||
* Renesas DK-S7G2 board config | |||
* Altera EP3C10 FPGA (Cyclone III family) target config | |||
* TI MSP432P4xx target config | |||
* Cypress PSoC 5LP target config | |||
* Analog Devices ADSP-SC58x target config (Cortex-A5 core only) | |||
Server Layer: | |||
* tcl_trace command for async target trace output via Tcl RPC | |||
Documentation: | |||
Build and Release: | |||
* Various fixes thanks to http://coccinellery.org/ | |||
* libftdi is now autodetected with pkgconfig | |||
* Releases should now support reproducible builds | |||
* Conversion to non-recursive make, requires automake >= 1.14 | |||
* Udev rules modified to add uaccess tag and moved to | |||
60-openocd.rules | |||
* Support searching for scripts relative to the openocd binary | |||
for all major architectures | |||
This release also contains a number of other important functional and | |||
cosmetic bugfixes. For more details about what has changed since the | |||
last release, see the git repository history: | |||
http://sourceforge.net/p/openocd/code/ci/v0.10.0/log/?path= | |||
http://sourceforge.net/p/openocd/code/ci/v0.x.0/log/?path= | |||
For older NEWS, see the NEWS files associated with each release | |||
@@ -0,0 +1,155 @@ | |||
This file includes highlights of the changes made in the OpenOCD | |||
source archive release. | |||
JTAG Layer: | |||
* New driver for J-Link adapters based on libjaylink | |||
(including support for FPGA configuration, SWO and EMUCOM) | |||
* FTDI improvements to work at 30MHz clock | |||
* BCM2835 native driver SWD and Raspberry Pi2 support | |||
* BCM2835 is set to 4ma drive, slow slew rate | |||
* ixo-usb-jtag (emulation of an Altera Bus Blaster I on | |||
Cypress FX2 IC) support | |||
* JTAG pass-through mode for CMSIS-DAP (including support for | |||
FPGA configuration) | |||
* OpenJTAG support for Cypress CY7C65215 | |||
* connect_assert_srst support for SWD | |||
* Xilinx Virtex-II Series7 bitstream loading support | |||
* Use JEP106 data to decode IDs | |||
* Deprecated "ft2232" driver removed (use "ftdi" instead) | |||
* GPL-incompatible FTDI D2XX library support dropped (Presto, | |||
OpenJTAG and USB-Blaster I are using libftdi only now) | |||
* ZY1000 support dropped (unmaintained since long) | |||
* oocd_trace support dropped | |||
Boundary Scan: | |||
Target Layer: | |||
* ARMv7-A, Cortex-M, Cortex-A/R important fixes and | |||
improvements (allowing e.g. simultaneous debugging of A8 and | |||
M3 cores, JTAG WAIT support etc.) | |||
* ARM Cortex-A,R allow interrupt disable during single-step | |||
(maskisr command) | |||
* Semihosting support for ARMv7-A | |||
* ARM Cortex-M7 support | |||
* Intel Quark mcu D2000 support | |||
* Freescale LS102x SAP support | |||
* ThreadX RTOS support on ARM926E-JS | |||
* Cortex-M RTOS stack alignment fixes | |||
* FreeRTOS FPU support | |||
* uC/OS-III RTOS support | |||
* bridging semihosting to GDB's File-I/O support | |||
* -defer-examine option added to target create command | |||
* verify_image_checksum command added | |||
Flash Layer: | |||
* Atmel SAM4S, SAM4N, SAM4C support | |||
* Atmel SAMV, SAMS, SAME (Cortex-M7) support | |||
* Atmel AT91SAMD handle reset run/halt in DSU, other fixes | |||
* Atmel AT91SAML21, SAML22, SAMC20/SAMC21, SAMD09 support | |||
* ST STM32F4x support | |||
* ST STM32F74x/76x/77x, STM32L4 support | |||
* ST STM32L0 categories 1, 2 and 5 support | |||
* Kinetis K02, K21, K22, K24, K26, K63, K64, K66 support | |||
* Kinetis KE, KVx, K8x families support | |||
* Kinetis FlexNVM handling | |||
* Kinetis flash protection, security, mass_erase improvements | |||
* Infineon XMC4xxx family support | |||
* Infineon XMC1000 flash driver | |||
* Energy Micro EFM32 Happy Gecko support | |||
* Energy Micro EFM32 debug interface lock support | |||
* Analog Devices ADuCM360 support | |||
* Unified Nuvoton NuMicro flash driver | |||
* NIIET K1921VK01T (Cortex-M4) support | |||
* Nordic Semiconductor nRF51 improvements | |||
* Spansion FM4 flash (including MB9BFx64/x65, S6E2DH) driver | |||
* Ambiq Micro Apollo flash driver | |||
* PIC32MX new device IDs, 17x/27x flash support | |||
* read_bank() and verify_bank() NOR flash internal API to | |||
allow reading (and verifying) non-memory-mapped devices | |||
* JTAGSPI driver to access SPI NOR flashes via a trivial | |||
FPGA proxy | |||
* Milandr read/verify for Info memory support | |||
* Various discrete SPI NOR flashes support | |||
* CFI 16-bit flash reversed endianness support | |||
Board, Target, and Interface Configuration Scripts: | |||
* Digilent JTAG-HS2, JTAG-HS3 interfaces configs | |||
* FTDI UM232H module as JTAG interface config | |||
* 100ask's OpenJTAG interface config | |||
* MBFTDI interface config | |||
* XDS100v3 interface config | |||
* Freescale Vybrid VF6xx target config | |||
* EmCraft VF6 SOM and baseboard configs | |||
* Freescale SabreSD board config | |||
* Freescale VF65GS10 tower board config | |||
* Pipistrello Xilinx Spartan6 LX45 FPGA board config | |||
* miniSpartan6+ board config | |||
* Xilinx Kintex7 Development board config | |||
* Parallella-I board config | |||
* Digilent Atlys and Analog Discovery board configs | |||
* Numato Opsis board config | |||
* Xilinx Spartan 6 FPGA "Device DNA" reading support | |||
* Altera 10M50 FPGA (MAX10 family) target config | |||
* Altera EPM240 CPLD (MAXII family) target config | |||
* Marsohod2, Marsohod3 FPGA, Marsohod CPLD boards configs | |||
* Novena's integrated FPGA board config | |||
* XMOS XS1-XAU8A-10's ARM core config | |||
* XMOS xCORE-XA Core Module board config | |||
* Exynos5250 target config | |||
* Arndale board config | |||
* FM4 MB9BFxxx family configs | |||
* Spansion SK-FM4-U120-9B560 board config | |||
* Diolan LPC4357-DB1 board config | |||
* ST STM32F469 discovery board config | |||
* ST STM32F7-DISCO, STM327[4|5]6G-EVAL boards configs | |||
* ST STM32L4 discovery, NUCLEO L476RG, STM32F429I-DISC1 boards | |||
configs | |||
* Atheros AR2313, AR2315 targets config | |||
* Netgear WP102 board config | |||
* La Fonera FON2200 board config | |||
* Linksys WAG200G board config | |||
* LPC-Link2 board config | |||
* NXP LPC4370 target config | |||
* Atmel SAMV, SAMS, SAME target configs | |||
* Atmel SAM E70 Xplained, SAM V71 Xplained Ultra boards | |||
configs | |||
* Nordic nRF52 target config | |||
* Nordic nRF51-DK, nRF52-DK boards configs | |||
* Infineon XMC4700 Relax Kit, XMC4800 Relax EtherCAT Kit, | |||
XMC4300 Relax EtherCAT Kit boards configs | |||
* Renesas S7G2 target config | |||
* Renesas DK-S7G2 board config | |||
* Altera EP3C10 FPGA (Cyclone III family) target config | |||
* TI MSP432P4xx target config | |||
* Cypress PSoC 5LP target config | |||
* Analog Devices ADSP-SC58x target config (Cortex-A5 core only) | |||
Server Layer: | |||
* tcl_trace command for async target trace output via Tcl RPC | |||
Documentation: | |||
Build and Release: | |||
* Various fixes thanks to http://coccinellery.org/ | |||
* libftdi is now autodetected with pkgconfig | |||
* Releases should now support reproducible builds | |||
* Conversion to non-recursive make, requires automake >= 1.14 | |||
* Udev rules modified to add uaccess tag and moved to | |||
60-openocd.rules | |||
* Support searching for scripts relative to the openocd binary | |||
for all major architectures | |||
This release also contains a number of other important functional and | |||
cosmetic bugfixes. For more details about what has changed since the | |||
last release, see the git repository history: | |||
http://sourceforge.net/p/openocd/code/ci/v0.10.0/log/?path= | |||
For older NEWS, see the NEWS files associated with each release | |||
(i.e. NEWS-<version>). | |||
For more information about contributing test reports, bug fixes, or new | |||
features and device support, please read the new Developer Manual (or | |||
the BUGS and PATCHES.txt files in the source archive). |
@@ -1,5 +1,5 @@ | |||
AC_PREREQ(2.64) | |||
AC_INIT([openocd], [0.10.0], | |||
AC_INIT([openocd], [0.10.0+dev], | |||
[OpenOCD Mailing List <openocd-devel@lists.sourceforge.net>]) | |||
AC_CONFIG_SRCDIR([src/openocd.c]) | |||