scripts: use adapter_khz not deprecated jtag_khz

Change-Id: Ibaeebf564a95360dcf21a0921ec99f5263f11915
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/202
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>

tcl/board/at91cap7a-stk-sdram.cfg

@@ -28,7 +28,7 @@ target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAM
 
 $_TARGETNAME configure -event reset-start {
 	# start off real slow when we're running off internal RC oscillator
-	jtag_khz 32
+	adapter_khz 32
 }
 
 proc peek32 {address} {
@@ -78,7 +78,7 @@ $_TARGETNAME configure -event reset-init {
 	echo "Master clock ok."
 	
 	# Now that we're up and running, crank up speed!
-	global post_reset_khz ;	jtag_khz $post_reset_khz
+	global post_reset_khz ;	adapter_khz $post_reset_khz
 	
 	echo "Configuring the SDRAM controller..."
 

tcl/board/mcb1700.cfg

@@ -11,7 +11,7 @@ set MCB1700_CCLK $CCLK
 $_TARGETNAME configure -event reset-start {
 	# Start *real slow* as we do not know the
     # state the boot rom left the clock in
-	jtag_khz 10
+	adapter_khz 10
 }
 
 # Set up 100MHz clock to CPU
@@ -55,7 +55,7 @@ $_TARGETNAME configure -event reset-init {
 	#
 	# 
 	global MCB1700_CCLK
-	jtag_khz [expr $MCB1700_CCLK / 8]
+	adapter_khz [expr $MCB1700_CCLK / 8]
 
 	# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
 	# "User Flash Mode" where interrupt vectors are _not_ remapped,

tcl/interface/hilscher_nxhx10_etm.cfg

@@ -8,4 +8,4 @@ interface ft2232
 ft2232_device_desc "NXHX 10-ETM"
 ft2232_layout comstick
 ft2232_vid_pid 0x0640 0x0028
-jtag_khz 6000
+adapter_khz 6000

tcl/interface/hilscher_nxhx500_etm.cfg

@@ -8,4 +8,4 @@ interface ft2232
 ft2232_device_desc "NXHX 500-ETM"
 ft2232_layout comstick
 ft2232_vid_pid 0x0640 0x0028
-jtag_khz 6000
+adapter_khz 6000

tcl/interface/hilscher_nxhx500_re.cfg

@@ -8,4 +8,4 @@ interface ft2232
 ft2232_device_desc "NXHX 500-RE"
 ft2232_layout comstick
 ft2232_vid_pid 0x0640 0x0028
-jtag_khz 6000
+adapter_khz 6000

tcl/interface/hilscher_nxhx50_etm.cfg

@@ -8,4 +8,4 @@ interface ft2232
 ft2232_device_desc "NXHX 50-ETM"
 ft2232_layout comstick
 ft2232_vid_pid 0x0640 0x0028
-jtag_khz 6000
+adapter_khz 6000

tcl/interface/hilscher_nxhx50_re.cfg

@@ -8,4 +8,4 @@ interface ft2232
 ft2232_device_desc "NXHX50-RE"
 ft2232_layout comstick
 ft2232_vid_pid 0x0640 0x0028
-jtag_khz 6000
+adapter_khz 6000

tcl/target/lpc1768.cfg

@@ -52,7 +52,7 @@ flash bank $_FLASHNAME lpc2000 0x0 0x80000 0 0 $_TARGETNAME \
 # Run with *real slow* clock by default since the
 # boot rom could have been playing with the PLL, so
 # we have no idea what clock the target is running at.
-jtag_khz 10
+adapter_khz 10
 
 $_TARGETNAME configure -event reset-init {
 	# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select

tcl/target/stm32f2x.cfg

@@ -26,7 +26,7 @@ if { [info exists WORKAREASIZE] } {
 # bit more to be on the safe side. Perhaps superstition, but if are
 # running off a crystal, we can run closer to the limit. Note
 # that there can be a pretty wide band where things are more or less stable.
-jtag_khz 1000
+adapter_khz 1000
 
 jtag_nsrst_delay 100
 jtag_ntrst_delay 100