remove obsolete reset_mode

git-svn-id: svn://svn.berlios.de/openocd/trunk@833 b42882b7-edfa-0310-969c-e2dbd0fdcd60

src/target/target/at91r40008.cfg

@@ -10,7 +10,7 @@ jtag_device 4 0x1 0xf 0xe
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_init 0 arm7tdmi
+target arm7tdmi little 0 arm7tdmi
 run_and_halt_time 0 30
 
 target_script 0 reset event/at91r40008_reset.script

src/target/target/at91sam9260.cfg

@@ -15,7 +15,7 @@ jtag_ntrst_delay 0
 ######################
 
 #target <type> <endianess> <reset mode> <JTAG pos> <variant>
-target arm926ejs little reset_init 0 arm926ejs
+target arm926ejs little 0 arm926ejs
 
 target_script 0 reset event/at91sam9260_reset.script
 run_and_halt_time 0 30

src/target/target/at91sam9260minimal.cfg

@@ -15,6 +15,6 @@ jtag_ntrst_delay 200
 ######################
 
 #target <type> <endianess> <reset mode> <JTAG pos> <variant>
-target arm926ejs little reset_run 0 arm926ejs
+target arm926ejs little 0 arm926ejs
 run_and_halt_time 0 30
 

src/target/target/eir-sam7se512.cfg

@@ -10,7 +10,7 @@ daemon_startup reset
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_init 0 arm7tdmi
+target arm7tdmi little 0 arm7tdmi
 run_and_halt_time 0 30
 
 target_script 0 reset event/eir-sam7se512_reset.script

src/target/target/epc9301.cfg

@@ -5,7 +5,7 @@ jtag_ntrst_delay 100
 #target configuration
 daemon_startup attach
 #target <type> <endianess> <reset mode>
-target arm920t little reset_halt 0
+target arm920t little 0
 working_area 0 0x80014000 0x1000 backup
 #flash configuration
 #flash bank <driver> <base> <size> <chip_width> <bus_width> [driver_options ...]

src/target/target/hammer.cfg

@@ -12,7 +12,7 @@ jtag_device 4 0x1 0xf 0xe
 #target configuration
 daemon_startup reset
 #target <type> <endianess> <reset mode>
-target arm920t little run_and_init 0 arm920t
+target arm920t little 0 arm920t
 
 # speed up memory downloads
 arm7 fast_memory_access enable

src/target/target/ipx42x.cfg

@@ -9,5 +9,5 @@ jtag_device 7 0x1 0x7f 0x7e
 daemon_startup reset
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target xscale big run_and_halt 0 IXP42x
+target xscale big 0 IXP42x
 run_and_halt_time 0 30

src/target/target/lm3s6965.cfg

@@ -16,7 +16,7 @@ jtag_device 4 0x1 0xf 0xe
 # the luminary variant causes a software reset rather than asserting SRST
 # this stops the debug registers from being cleared
 # this will be fixed in later revisions of silicon
-target cortex_m3 little reset_halt 0 lm3s
+target cortex_m3 little 0 lm3s
 
 # 4k working area at base of ram
 working_area 0 0x20000000 0x4000 nobackup

src/target/target/lm3s811.cfg

@@ -16,7 +16,7 @@ jtag_device 4 0x1 0xf 0xe
 # the luminary variant causes a software reset rather than asserting SRST
 # this stops the debug registers from being cleared
 # this will be fixed in later revisions of silicon
-target cortex_m3 little reset_halt 0 lm3s
+target cortex_m3 little 0 lm3s
 
 # 8k working area at base of ram
 working_area 0 0x20000000 0x2000 nobackup

src/target/target/lpc2129.cfg

@@ -8,7 +8,7 @@ jtag_device 4 0x1 0xf 0xe
 daemon_startup reset
 #target <type> <startup mode>
 #target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4
+target arm7tdmi little 0 arm7tdmi-s_r4
 run_and_halt_time 0 30
 working_area 0 0x40000000 0x4000 nobackup
 #flash bank <driver> <base> <size> <chip_width> <bus_width>

src/target/target/lpc2148.cfg

@@ -15,7 +15,7 @@ jtag_device 4 0x1 0xf 0xe
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_init 0 arm7tdmi-s_r4
+target arm7tdmi little 0 arm7tdmi-s_r4
 run_and_halt_time 0 30
 
 target_script 0 reset event/lpc2148_reset.script

src/target/target/lpc2294.cfg

@@ -7,7 +7,7 @@ jtag_device 4 0x1 0xf 0xe
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4
+target arm7tdmi little 0 arm7tdmi-s_r4
 run_and_halt_time 0 30
 
 working_area 0 0x40000000 0x4000 nobackup

src/target/target/mx31.cfg

@@ -11,6 +11,6 @@ jtag_device 4 0x0 0x0 0xe
 jtag_device 5 0x1 0x0 0x1e 
 
 #target <type> <endianess> <reset mode>
-target arm11 little reset_halt 1
+target arm11 little 1
 run_and_halt_time 0 0
 

src/target/target/netx500.cfg

@@ -9,5 +9,5 @@ jtag_ntrst_delay 100
 #target configuration
 daemon_startup reset
 #target <type> <endianness> <startup mode> <chainpos> <variant>
-target arm926ejs little run_and_halt 0 arm926ejs
+target arm926ejs little 0 arm926ejs
 run_and_halt_time 0 500

src/target/target/nslu2.cfg

@@ -6,7 +6,7 @@ reset_config srst_only
 jtag_device 7 0x1 0x7f 0x7e
 
 # target configuration
-target xscale big reset_init 0 ixp42x
+target xscale big 0 ixp42x
 run_and_halt_time 0 30
 
 # maps to PXA internal RAM.  If you are using a PXA255

src/target/target/omap5912.cfg

@@ -14,7 +14,7 @@ jtag_device 8  0x0 0x0 0x0
 daemon_startup reset
 
 #target <type> <endianness> <reset mode> <chainpos> <variant>
-target arm926ejs little run_and_init 1 arm926ejs
+target arm926ejs little 1 arm926ejs
 target_script 0 reset event/omap5912_reset.script
 run_and_halt_time 0 30
 

src/target/target/pxa255.cfg

@@ -1,7 +1,7 @@
 jtag_device 5 0x1 0x1f 0x1e
 jtag_nsrst_delay 200
 jtag_ntrst_delay 200
-target xscale little reset_init 0 pxa255
+target xscale little 0 pxa255
 reset_config trst_and_srst
 run_and_halt_time 0 30
 

src/target/target/pxa270.cfg

@@ -12,7 +12,7 @@ reset_config trst_and_srst separate
 jtag_device 7 0x1 0x7f 0x7e
 #target configuration
 daemon_startup reset
-target xscale little reset_halt 0 pxa27x
+target xscale little 0 pxa27x
 # maps to PXA internal RAM. If you are using a PXA255
 # you must initialize SDRAM or leave this option off
 working_area 0 0x5c000000 0x10000 nobackup

src/target/target/sam7s256.cfg

@@ -7,7 +7,7 @@ jtag_device 4 0x1 0xf 0xe
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_init 0 arm7tdmi
+target arm7tdmi little 0 arm7tdmi
 run_and_halt_time 0 30
 
 target_script 0 reset event/sam7s256_reset.script

src/target/target/sam7x256.cfg

@@ -7,7 +7,7 @@ jtag_device 4 0x1 0xf 0xe
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_init 0 arm7tdmi
+target arm7tdmi little 0 arm7tdmi
 run_and_halt_time 0 30
 
 target_script 0 reset event/sam7x256_reset.script

src/target/target/stm32.cfg

@@ -16,7 +16,7 @@ jtag_device 5 0x1 0x1 0x1e
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target cortex_m3 little reset_halt 0
+target cortex_m3 little 0
 run_and_halt_time 0 30
 
 working_area 0 0x20000000 16384 nobackup

src/target/target/stm32stick.cfg

@@ -17,7 +17,7 @@ jtag_device 4 0x1 0xf 0xe
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target cortex_m3 little reset_halt 0
+target cortex_m3 little 0
 run_and_halt_time 0 30
 
 working_area 0 0x20000000 16384 nobackup

src/target/target/str710.cfg

@@ -10,7 +10,7 @@ jtag_device 4 0x1 0xf 0xe
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
+target arm7tdmi little 0 arm7tdmi
 run_and_halt_time 0 30
 
 target_script 0 gdb_program_config event/str710_program.script

src/target/target/str730.cfg

@@ -19,7 +19,7 @@ daemon_startup reset
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
+target arm7tdmi little 0 arm7tdmi
 
 run_and_halt_time 0 30
 

src/target/target/str750.cfg

@@ -20,7 +20,7 @@ daemon_startup reset
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
+target arm7tdmi little 0 arm7tdmi
 
 run_and_halt_time 0 30
 

src/target/target/str912.cfg

@@ -17,7 +17,7 @@ jtag_device 5 0x1 0x1 0x1e
 
 #target <type> <startup mode>
 #target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm966e little reset_halt 1 arm966e
+target arm966e little 1 arm966e
 run_and_halt_time 0 30
 
 target_script 0 reset event/str912_reset.script

src/target/target/str9comstick.cfg

@@ -16,7 +16,7 @@ jtag_device 5 0x1 0x1 0x1e
 daemon_startup reset
 #target <type> <startup mode>
 #target arm966e <endianness> <reset mode> <chainpos> <variant>
-target arm966e little reset_halt 1 arm966e
+target arm966e little 1 arm966e
 run_and_halt_time 0 30
 working_area 0 0x50000000 16384 nobackup
 #flash bank <driver> <base> <size> <chip_width> <bus_width>

src/target/target/wi-9c.cfg

@@ -15,7 +15,7 @@ jtag_ntrst_delay 0
 ######################
 
 #target <type> <endianess> <reset mode> <JTAG pos> <variant>
-target arm926ejs big reset_init 0 arm926ejs
+target arm926ejs big 0 arm926ejs
 
 target_script 0 reset event/wi-9c_reset.script
 run_and_halt_time 0 30

src/target/target/xba_revA3.cfg

@@ -12,8 +12,8 @@ jtag_device 7 0x1 0x7f 0x7e
 daemon_startup reset
 
 #target <type> <endianess> <reset mode> <JTAG pos> <variant>
-target  xscale big         reset_init   0          ixp42x
-#target  xscale big         run_and_halt   0          ixp42x
+target  xscale big           0          ixp42x
+#target  xscale big           0          ixp42x
 target_script 0 reset event/xba_revA3.script
 
 run_and_halt_time 0 100

src/target/target/zy1000.cfg

@@ -14,7 +14,7 @@ reset_config srst_only srst_pulls_trst
 jtag_device 4 0x1 0xf 0xe
 
 #target configuration
-target arm7tdmi little reset_init 0 arm7tdmi-s_r4
+target arm7tdmi little 0 arm7tdmi-s_r4
 
 # at CPU CLK <32kHz this must be disabled
 arm7 fast_memory_access enable