- Moved variant-independent code to lpc17xx.cfg, which will be included from lpc17??.cfg files automatically. - lpc1768.cfg filled with variant-dependent code. Change-Id: I7dabe6ed7da7be640ed38c13aaaa096b8796d9a0 Signed-off-by: Vandra Akos <axos88@gmail.com> Reviewed-on: http://openocd.zylin.com/675 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>tags/v0.6.0-rc1
@@ -1,14 +1,8 @@ | |||||
# NXP LPC1768 Cortex-M3 with 512kB Flash and 32kB+32kB Local On-Chip SRAM, | # NXP LPC1768 Cortex-M3 with 512kB Flash and 32kB+32kB Local On-Chip SRAM, | ||||
# LPC17xx chips support both JTAG and SWD transports. | |||||
# Adapt based on what transport is active. | |||||
source [find target/swj-dp.tcl] | |||||
if { [info exists CHIPNAME] } { | |||||
set _CHIPNAME $CHIPNAME | |||||
} else { | |||||
set _CHIPNAME lpc1768 | |||||
} | |||||
set CHIPNAME lpc1768 | |||||
set CPUTAPID 0x4ba00477 | |||||
set CPURAMSIZE 0x8000 | |||||
set CPUROMSIZE 0x80000 | |||||
# After reset the chip is clocked by the ~4MHz internal RC oscillator. | # After reset the chip is clocked by the ~4MHz internal RC oscillator. | ||||
# When board-specific code (reset-init handler or device firmware) | # When board-specific code (reset-init handler or device firmware) | ||||
@@ -17,70 +11,7 @@ if { [info exists CHIPNAME] } { | |||||
# (The ROM code doing those updates cares about core clock speed...) | # (The ROM code doing those updates cares about core clock speed...) | ||||
# | # | ||||
# CCLK is the core clock frequency in KHz | # CCLK is the core clock frequency in KHz | ||||
if { [info exists CCLK] } { | |||||
set _CCLK $CCLK | |||||
} else { | |||||
set _CCLK 4000 | |||||
} | |||||
if { [info exists CPUTAPID] } { | |||||
set _CPUTAPID $CPUTAPID | |||||
} else { | |||||
set _CPUTAPID 0x4ba00477 | |||||
} | |||||
if { [info exists CPURAMSIZE] } { | |||||
set _CPURAMSIZE $CPURAMSIZE | |||||
} else { | |||||
set _CPURAMSIZE 0x8000 | |||||
} | |||||
if { [info exists CPUROMSIZE] } { | |||||
set _CPUROMSIZE $CPUROMSIZE | |||||
} else { | |||||
set _CPUROMSIZE 0x80000 | |||||
} | |||||
#delays on reset lines | |||||
adapter_nsrst_delay 200 | |||||
jtag_ntrst_delay 200 | |||||
#jtag newtap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID | |||||
swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID | |||||
set _TARGETNAME $_CHIPNAME.cpu | |||||
target create $_TARGETNAME cortex_m3 -chain-position $_TARGETNAME | |||||
# LPC1768 has 32kB of SRAM In the ARMv7-M "Code" area (at 0x10000000) | |||||
# and 32K more on AHB, in the ARMv7-M "SRAM" area, (at 0x2007c000). | |||||
$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size $_CPURAMSIZE | |||||
# LPC1768 has 512kB of flash memory, managed by ROM code (including a | |||||
# boot loader which verifies the flash exception table's checksum). | |||||
# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum] | |||||
set _FLASHNAME $_CHIPNAME.flash | |||||
flash bank $_FLASHNAME lpc2000 0x0 $_CPUROMSIZE 0 0 $_TARGETNAME \ | |||||
lpc1700 $_CCLK calc_checksum | |||||
# Run with *real slow* clock by default since the | |||||
# boot rom could have been playing with the PLL, so | |||||
# we have no idea what clock the target is running at. | |||||
adapter_khz 10 | |||||
$_TARGETNAME configure -event reset-init { | |||||
# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select | |||||
# "User Flash Mode" where interrupt vectors are _not_ remapped, | |||||
# and reside in flash instead). | |||||
# | |||||
# See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description | |||||
# Bit Symbol Value Description Reset | |||||
# value | |||||
# 0 MAP Memory map control. 0 | |||||
# 0 Boot mode. A portion of the Boot ROM is mapped to address 0. | |||||
# 1 User mode. The on-chip Flash memory is mapped to address 0. | |||||
# 31:1 - Reserved. The value read from a reserved bit is not defined. NA | |||||
# | |||||
# http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user | |||||
set CCLK 4000 | |||||
mww 0x400FC040 0x01 | |||||
} | |||||
#Include the main configuration file. | |||||
source [find target/lpc17xx.cfg]; |
@@ -0,0 +1,93 @@ | |||||
# Main file for NXP LPC17xx Cortex-M3 | |||||
# | |||||
# !!!!!! | |||||
# | |||||
# This file should not be included directly, rather | |||||
# by the lpc1751.cfg, lpc1752.cfg, etc. which set the | |||||
# needed variables to the appropriate values. | |||||
# | |||||
# !!!!!! | |||||
# LPC17xx chips support both JTAG and SWD transports. | |||||
# Adapt based on what transport is active. | |||||
source [find target/swj-dp.tcl] | |||||
if { [info exists CHIPNAME] } { | |||||
set _CHIPNAME $CHIPNAME | |||||
} else { | |||||
error "_CHIPNAME not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)." | |||||
} | |||||
# After reset the chip is clocked by the ~4MHz internal RC oscillator. | |||||
# When board-specific code (reset-init handler or device firmware) | |||||
# configures another oscillator and/or PLL0, set CCLK to match; if | |||||
# you don't, then flash erase and write operations may misbehave. | |||||
# (The ROM code doing those updates cares about core clock speed...) | |||||
# | |||||
# CCLK is the core clock frequency in KHz | |||||
if { [info exists CCLK] } { | |||||
set _CCLK $CCLK | |||||
} else { | |||||
set _CCLK 4000 | |||||
} | |||||
if { [info exists CPUTAPID] } { | |||||
set _CPUTAPID $CPUTAPID | |||||
} else { | |||||
error "_CPUTAPID not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)." | |||||
} | |||||
if { [info exists CPURAMSIZE] } { | |||||
set _CPURAMSIZE $CPURAMSIZE | |||||
} else { | |||||
error "_CPURAMSIZE not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)." | |||||
} | |||||
if { [info exists CPUROMSIZE] } { | |||||
set _CPUROMSIZE $CPUROMSIZE | |||||
} else { | |||||
error "_CPUROMSIZE not set. Please do not include lpc17xx.cfg directly, but the specific chip configuration file (lpc1751.cfg, lpc1764.cfg, etc)." | |||||
} | |||||
#delays on reset lines | |||||
adapter_nsrst_delay 200 | |||||
jtag_ntrst_delay 200 | |||||
#jtag newtap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID | |||||
swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID | |||||
set _TARGETNAME $_CHIPNAME.cpu | |||||
target create $_TARGETNAME cortex_m3 -chain-position $_TARGETNAME | |||||
# The LPC17xx devices have 8/16/32kB of SRAM In the ARMv7-M "Code" area (at 0x10000000) | |||||
$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size $_CPURAMSIZE | |||||
# The LPC17xx devies have 32/64/128/256/512kB of flash memory, managed by ROM code | |||||
# (including a boot loader which verifies the flash exception table's checksum). | |||||
# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum] | |||||
set _FLASHNAME $_CHIPNAME.flash | |||||
flash bank $_FLASHNAME lpc2000 0x0 $_CPUROMSIZE 0 0 $_TARGETNAME \ | |||||
lpc1700 $_CCLK calc_checksum | |||||
# Run with *real slow* clock by default since the | |||||
# boot rom could have been playing with the PLL, so | |||||
# we have no idea what clock the target is running at. | |||||
adapter_khz 10 | |||||
$_TARGETNAME configure -event reset-init { | |||||
# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select | |||||
# "User Flash Mode" where interrupt vectors are _not_ remapped, | |||||
# and reside in flash instead). | |||||
# | |||||
# See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description | |||||
# Bit Symbol Value Description Reset | |||||
# value | |||||
# 0 MAP Memory map control. 0 | |||||
# 0 Boot mode. A portion of the Boot ROM is mapped to address 0. | |||||
# 1 User mode. The on-chip Flash memory is mapped to address 0. | |||||
# 31:1 - Reserved. The value read from a reserved bit is not defined. NA | |||||
# | |||||
# http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user | |||||
mww 0x400FC040 0x01 | |||||
} |