Browse Source

fix syntax of mww phys.

tags/v0.3.0-rc0
Øyvind Harboe 12 years ago
parent
commit
a07422c26c
5 changed files with 44 additions and 44 deletions
  1. +1
    -1
      tcl/board/atmel_at91sam9260-ek.cfg
  2. +30
    -30
      tcl/board/mini2440.cfg
  3. +1
    -1
      tcl/board/olimex_sam9_l9260.cfg
  4. +1
    -1
      tcl/board/unknown_at91sam9260.cfg
  5. +11
    -11
      tcl/target/davinci.cfg

+ 1
- 1
tcl/board/atmel_at91sam9260-ek.cfg View File

@@ -24,7 +24,7 @@ $_TARGETNAME configure -event reset-start {
jtag_rclk 5
halt
# RSTC_MR : enable user reset, MMU may be enabled... use physical address
arm926ejs mww phys 0xfffffd08 0xa5000501
mww phys 0xfffffd08 0xa5000501
}

$_TARGETNAME configure -event reset-init {


+ 30
- 30
tcl/board/mini2440.cfg View File

@@ -177,10 +177,10 @@ proc init_2440 { } {
# usb clock are off 12mHz xtal
#-----------------------------------------------

arm920t mww phys 0x4C000014 0x00000005 # Clock Divider control Reg
arm920t mww phys 0x4C000000 0xFFFFFFFF # LOCKTIME count register
arm920t mww phys 0x4C000008 0x00038022 # UPPLCON USB clock config Reg
arm920t mww phys 0x4C000004 0x0007F021 # MPPLCON Proc clock config Reg
mww phys 0x4C000014 0x00000005 # Clock Divider control Reg
mww phys 0x4C000000 0xFFFFFFFF # LOCKTIME count register
mww phys 0x4C000008 0x00038022 # UPPLCON USB clock config Reg
mww phys 0x4C000004 0x0007F021 # MPPLCON Proc clock config Reg

#-----------------------------------------------
# Configure Memory controller
@@ -188,45 +188,45 @@ proc init_2440 { } {
# DRAM - 64MB - 32 bit bus, uses BANKCON6 BANKCON7
#-----------------------------------------------

arm920t mww phys 0x48000000 0x22111112 # BWSCON - Bank and Bus Width
arm920t mww phys 0x48000010 0x00001112 # BANKCON4 - ?
arm920t mww phys 0x4800001c 0x00018009 # BANKCON6 - DRAM
arm920t mww phys 0x48000020 0x00018009 # BANKCON7 - DRAM
arm920t mww phys 0x48000024 0x008E04EB # REFRESH - DRAM
arm920t mww phys 0x48000028 0x000000B2 # BANKSIZE - DRAM
arm920t mww phys 0x4800002C 0x00000030 # MRSRB6 - DRAM
arm920t mww phys 0x48000030 0x00000030 # MRSRB7 - DRAM
mww phys 0x48000000 0x22111112 # BWSCON - Bank and Bus Width
mww phys 0x48000010 0x00001112 # BANKCON4 - ?
mww phys 0x4800001c 0x00018009 # BANKCON6 - DRAM
mww phys 0x48000020 0x00018009 # BANKCON7 - DRAM
mww phys 0x48000024 0x008E04EB # REFRESH - DRAM
mww phys 0x48000028 0x000000B2 # BANKSIZE - DRAM
mww phys 0x4800002C 0x00000030 # MRSRB6 - DRAM
mww phys 0x48000030 0x00000030 # MRSRB7 - DRAM

#-----------------------------------------------
# Now port configuration for enables for memory
# and other stuff.
#-----------------------------------------------

arm920t mww phys 0x56000000 0x007FFFFF # GPACON
mww phys 0x56000000 0x007FFFFF # GPACON

arm920t mww phys 0x56000010 0x00295559 # GPBCON
arm920t mww phys 0x56000018 0x000003FF # GPBUP (PULLUP ENABLE)
arm920t mww phys 0x56000014 0x000007C2 # GPBDAT
mww phys 0x56000010 0x00295559 # GPBCON
mww phys 0x56000018 0x000003FF # GPBUP (PULLUP ENABLE)
mww phys 0x56000014 0x000007C2 # GPBDAT

arm920t mww phys 0x56000020 0xAAAAA6AA # GPCCON
arm920t mww phys 0x56000028 0x0000FFFF # GPCUP
arm920t mww phys 0x56000024 0x00000020 # GPCDAT
mww phys 0x56000020 0xAAAAA6AA # GPCCON
mww phys 0x56000028 0x0000FFFF # GPCUP
mww phys 0x56000024 0x00000020 # GPCDAT

arm920t mww phys 0x56000030 0xAAAAAAAA # GPDCON
arm920t mww phys 0x56000038 0x0000FFFF # GPDUP
mww phys 0x56000030 0xAAAAAAAA # GPDCON
mww phys 0x56000038 0x0000FFFF # GPDUP

arm920t mww phys 0x56000040 0xAAAAAAAA # GPECON
arm920t mww phys 0x56000048 0x0000FFFF # GPEUP
mww phys 0x56000040 0xAAAAAAAA # GPECON
mww phys 0x56000048 0x0000FFFF # GPEUP

arm920t mww phys 0x56000050 0x00001555 # GPFCON
arm920t mww phys 0x56000058 0x0000007F # GPFUP
arm920t mww phys 0x56000054 0x00000000 # GPFDAT
mww phys 0x56000050 0x00001555 # GPFCON
mww phys 0x56000058 0x0000007F # GPFUP
mww phys 0x56000054 0x00000000 # GPFDAT

arm920t mww phys 0x56000060 0x00150114 # GPGCON
arm920t mww phys 0x56000068 0x0000007F # GPGUP
mww phys 0x56000060 0x00150114 # GPGCON
mww phys 0x56000068 0x0000007F # GPGUP

arm920t mww phys 0x56000070 0x0015AAAA # GPHCON
arm920t mww phys 0x56000078 0x000003FF # GPGUP
mww phys 0x56000070 0x0015AAAA # GPHCON
mww phys 0x56000078 0x000003FF # GPGUP

}



+ 1
- 1
tcl/board/olimex_sam9_l9260.cfg View File

@@ -26,7 +26,7 @@ $_TARGETNAME configure -event reset-start {
# RSTC_MR : enable user reset, reset length is 64 slow clock cycles. MMU may
# be enabled... use physical address.
arm926ejs mww phys 0xfffffd08 0xa5000501
mww phys 0xfffffd08 0xa5000501
}

$_TARGETNAME configure -event reset-init {


+ 1
- 1
tcl/board/unknown_at91sam9260.cfg View File

@@ -18,7 +18,7 @@ $_TARGETNAME configure -event reset-start {
jtag_rclk 3
halt
# RSTC_MR : enable user reset, MMU may be enabled... use physical address
arm926ejs mww phys 0xfffffd08 0xa5000501
mww phys 0xfffffd08 0xa5000501
}




+ 11
- 11
tcl/target/davinci.cfg View File

@@ -204,34 +204,34 @@ proc davinci_wdog_reset {} {
#

# EMUMGT_CLKSPEED: write FREE bit to run despite emulation halt
arm926ejs mww phys [expr $timer2_phys + 0x28] 0x00004000
mww phys [expr $timer2_phys + 0x28] 0x00004000

#
# Part II -- in case watchdog hasn't been set up
#

# TCR: disable, force internal clock source
arm926ejs mww phys [expr $timer2_phys + 0x20] 0
mww phys [expr $timer2_phys + 0x20] 0

# TGCR: reset, force to 64-bit wdog mode, un-reset ("initial" state)
arm926ejs mww phys [expr $timer2_phys + 0x24] 0
arm926ejs mww phys [expr $timer2_phys + 0x24] 0x110b
mww phys [expr $timer2_phys + 0x24] 0
mww phys [expr $timer2_phys + 0x24] 0x110b

# clear counter (TIM12, TIM34) and period (PRD12, PRD34) registers
# so watchdog triggers ASAP
arm926ejs mww phys [expr $timer2_phys + 0x10] 0
arm926ejs mww phys [expr $timer2_phys + 0x14] 0
arm926ejs mww phys [expr $timer2_phys + 0x18] 0
arm926ejs mww phys [expr $timer2_phys + 0x1c] 0
mww phys [expr $timer2_phys + 0x10] 0
mww phys [expr $timer2_phys + 0x14] 0
mww phys [expr $timer2_phys + 0x18] 0
mww phys [expr $timer2_phys + 0x1c] 0

# WDTCR: put into pre-active state, then active
arm926ejs mww phys [expr $timer2_phys + 0x28] 0xa5c64000
arm926ejs mww phys [expr $timer2_phys + 0x28] 0xda7e4000
mww phys [expr $timer2_phys + 0x28] 0xa5c64000
mww phys [expr $timer2_phys + 0x28] 0xda7e4000

#
# Part III -- it's ready to rumble
#

# WDTCR: write invalid WDKEY to trigger reset
arm926ejs mww phys [expr $timer2_phys + 0x28] 0x00004000
mww phys [expr $timer2_phys + 0x28] 0x00004000
}

Loading…
Cancel
Save