Remove comment about workaround of not working 'reset halt' - not needed
as 'reset halt' is working as expected @ EDBG with srst_only.
Add srst_pulls_trst to reset_config as it no more triggers an error.
Change-Id: I47cf445690c46ccfb866900cddbfcaefc8649f82
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3722
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Purge all legacy interface configurations so there's no more confusion
over which one to use.
Also remove doc/INSTALL.txt which mentions ft2232 but otherwise just
duplicates what INSTALL says.
Change-Id: Ic94f808f123d4917e600b79309f1272c78a7bb11
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3236
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
At least on my (phyCORE-AM335X) system, the AM335x watchdog
needs to be disabled to use OpenOCD for more than 6.5 seconds
after reset.
Change-Id: I3d883a9f572b0ccb92f9864853a00c372e39d7f2
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Reviewed-on: http://openocd.zylin.com/3391
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Instead of updating these regularly we can just accept any IDCODE for the
boundary scan TAP.
The only downside might be that it's not immediately obvious if you
source a config for the wrong type of STM32.
Change-Id: I96d4d81699a491b3a46de3f0d3fd078ffddad4e4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3385
Tested-by: jenkins
Both boards use SEGGER interface.
nRF52 flash driver is in change 3511.
The board files were needed for transport select to SWD. The default
jtag transport didn't failover to SWD.
Change-Id: Id9c72aa88eeeb6a4e1999ee182f5284dbe535c05
Signed-off-by: Rick Foos <rfoos@solengtech.com>
Reviewed-on: http://openocd.zylin.com/3600
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik.hederstierna@gmail.com>
Reviewed-by: Michael Dietz <mjdietzx@gmail.com>
Reviewed-by: Jiří Pinkava <j-pi@seznam.cz>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The Linksys WAG200G router has a TI AR7 SoC and a 4MB Flash layout
similar to the Netgear DG834v3 router [1].
Below is an example of a successful flash recovery, using a TUMPA,
connected to the MIPS EJTAG 2.6 header (JP102) of the router.
WAG200G [2] TUMPA [3]
Desc Pin Pin Desc
------------------------
nTRST 1 3 nTRST
TDI 3 5 TDI
TDO 5 13 TDO
TMS 7 7 TMS
TCK 9 9 TCK
nSRST 11 15 RST
GND 2 4 GND
Note that nSRST is optional to halt the CPU, but is required to probe
the flash. For instance, recover the kernel with:
$ sudo ./src/openocd -s tcl \
-f interface/ftdi/tumpa.cfg \
-f tools/firmware-recovery.tcl \
-c 'board linksys-wag200g;
reset_config srst_only;
flash_part kernel /path/to/kernel.bin;
shutdown'
[1] https://wiki.openwrt.org/toh/linksys/wag200g
[2] https://www.linux-mips.org/wiki/JTAG#JTAG_headers
[3] http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User's_Manual#20_PIN_JTAG_Connector
Change-Id: I952ba9f706e2e4f8f95ca03a5fa58f391ca030b6
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-on: http://openocd.zylin.com/3776
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Kinetis driver checks MDM STAT register to detect secured state of MCU.
Original version often reported a blank device as secured one.
Change #3010 has not fixed all false reports.
After changes in arm_adi_v5 infrastructure secured devices was not detected
at all.
New algorithm uses multiple MDM STAT reads and counts MDM_STAT_SYSSEC and
MDM_STAT_FREADY bits. Both secured MCU and MCU locked-up in RESET/WDOG loop
are detected reliably.
Detection is run in both kx.cfg and klx.cfg from examine-start event,
not examine-end as before. Event is configured only for non hla adapter.
Minor fix in klx.cfg: commented out adapter_khz 24000 in reset-init.
Such frequency is not supported in VLPR CPU mode and with JTAG.
Change-Id: I2ec2b68c45bde9898159cd15fbdcbcfa538c41d9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3547
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
XDS100v3 is software compatible with the XDS100v2, but has a
different usb pid. This commit adds `xds100v3.cfg` that sources
the v2 one and changes the usb pid.
Change-Id: Ie29d325e8992d2de2f97d70862beeb63932ffa80
Signed-off-by: Remco Bloemen <openocd-gerrit@xn--2-umb.com>
Reviewed-on: http://openocd.zylin.com/3632
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
MBFTDI is a very cheap FT2232-based JTAG adapter
for programming Marsohod FPGA board.
Please see http://www.marsohod.org/prodmbftdi for details.
Change-Id: I35f758b49d1566098dc27f9581829cccad93ceeb
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/3604
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Increase workareasize when it is know we have a larger device.
Change-Id: Ieaee92e7cd25cc201989f14de122349698871412
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3378
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
PSoC4 design prevents reset halt/init with standard/low level
SWD adapter if hw reset line configured. Give user hint
to use 'reset_config none' in such case.
Change-Id: I0ca2c46b8575829b0013fd151f2eb63963d66653
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3617
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The IDCODE of Artix7 15T in the UG470 is wrong; Artix7 35T and 15T don't have the same IDCODE.
I've tested this on real hardware.
Change-Id: Iac267dc449c23454dd119126749dbeb8267c18ac
Signed-off-by: Felix Held <felix-openocd@felixheld.de>
Reviewed-on: http://openocd.zylin.com/3633
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Allow using physical addresses with mem2array and array2mem. In order
to minimize the impact on existing scripts, "phys" is added as an
optional 5th parameter to both commands.
This patch also adds "phys" variants to the memwrite/memread commands
in memory.tcl.
Change-Id: Ia6307f9d861789e7f3ccf1f98961d666bf8d85d6
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3387
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
add "mrb" command to read a byte of memory into a variable
Change-Id: I5ddc9fbcc55958a249548627bd15824df6dc0d61
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3542
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Just like observed with the General App Kit earlier, it now started to
fail halting:
SWD IDCODE 0x2ba01477
TARGET: xmc4500.cpu - Not halted
in procedure 'reset'
in procedure 'ocd_bouncer'
SWD IDCODE 0x2ba01477
Halt timed out, wake up GDB.
Rely on the target's default sysresetreq behavior to allow flashing to
work seemlessly again.
Change-Id: Ib9ce5f2c0ab99dca6d0fc74435fe26a58437fae5
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3416
Tested-by: jenkins
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested with TI MSP-EXP432P401R LaunchPad, via both on-board XDS110-ET (swd)
and external J-Link (jtag).
Change-Id: Ic0caa8516a155754b1c88a04acc8d3c511d9a5f7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3485
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The current configuration leads to the following error when trying to
program the target:
SWD IDCODE 0x2ba01477
timed out while waiting for target halted
TARGET: efm32.cpu - Not halted
in procedure 'program'
in procedure 'reset' called at file "embedded:startup.tcl", line 478
in procedure 'ocd_bouncer'
Use the default reset handling of the target (SYSRESETREQ) to reset the
system rather than SRST to fix the problem.
Tested on EFM32GG, EFM32TG and EZR32WG STK.
Change-Id: I788c41baf08b20814cbe0934b563424c4bc144b8
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3420
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It's Cortex-Xn, not Cortex Xn or cortex xn or cortex-xn or CORTEX-Xn
or CortexXn. Further it's Cortex-M0+, not M0plus.
Cf. http://www.arm.com/products/processors/index.php
Consistently write it the official way, so that it stops propagating.
Originally spotted in the documentation, it mainly affects code comments
but also Atmel SAM3/SAM4/SAMV, NiietCM4 and SiM3x flash driver output.
Found via:
git grep -i "Cortex "
git grep -i "Cortex-" | grep -v "Cortex-" | grep -v ".cpu"
git grep -i "CortexM"
Change-Id: Ic7b6ca85253e027f6f0f751c628d1a2a391fe914
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3483
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Both the STM32F429I-DISC{O,1} boards are equipped with the same MCU, but
differ by the debugging chip:
- the STM32F429I-DISCO uses the ST-LINK/V2 chip;
- the STM32F429I-DISC1 uses the ST-LINK/V2-B chip (which matches the USB
VID/PID set in stlink-v2-1.cfg).
Change-Id: I07d637f72d26cf5d714472638da974eb6ca02325
Signed-off-by: Samuel Martin <s.martin49@gmail.com>
Reviewed-on: http://openocd.zylin.com/3492
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The XMC1000 family uses a very different flash interface from XMC4000.
Tested on XMC 2Go and XMC1100 Boot Kit.
Change-Id: I3edaed420ef1c0fb89fdf221022c8b04163d41b3
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3418
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Tested with MKE04Z8VTG4, MKE02Z64VLC4 and MKE02Z64VLD2.
Change-Id: I606e32a2746a3b96d3e50f3656ba78d40c41c1ea
Signed-off-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-on: http://openocd.zylin.com/3380
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Leading zeros for the serial number are not necessary anymore.
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Change-Id: Ie4ff47b9cda7ccf314c6fda9a2784947db5ee4d9
Reviewed-on: http://openocd.zylin.com/3401
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Spansion FM4 family of microcontrollers does not offer a way to
identify the chip model nor the flash size, except for Dual Flash vs.
regular layout. Therefore the family is passed as argument and
wildcard-matched - MB9BFx6x and S6E2CC families are supported.
Iterations showed that ...
1) Just doing the flash command sequence from SRAM loader code for each
half-word took 20 minutes for an 8 KB block.
2) Doing the busy-wait in the loader merely reduced the time to 19 minutes.
3) Significant performance gains were achieved by looping in loader code
rather than in OpenOCD and by maximizing the batch size across sectors,
getting us down to ~2 seconds for 8 KB and ~2.5 minutes for 1.1 MB.
(Tested with SK-FM4-176L-S6E2CC-ETH v11, CMSIS-DAP v23.)
gcc, objcopy -Obinary and bin2char.sh are used for automating the
integration of hand-written assembler snippets.
Change-Id: I092c81074662534f50b71b91d54eb8e0098fec76
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2190
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The reset-init hook for this target speeds up the CPU clock and JTAG adapter
speed. When the target is reset running with high adapter speed, a series of
warnings "DAP transaction stalled (WAIT) - slowing down" will be generated
since the adapter speed is not reduced to fit the slower CPU speed.
Fix: reduction of the adapter speed before a reset is performed.
Change-Id: Iabfc8e3f70311e0e71c8eed09b8a37fcbed9c58d
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3365
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add support for the Intel Quark mcu D2000 using the new quark_d2xx
target.
Changes to the lakemont part are needed for the D2000 core and
backwards compatible with the X1000 one.
Change-Id: I6e1ef5a5d116344942f08e413965abd3945235fa
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/3199
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
niietcm4_write() buffer padding:
add correct buffer padding for 16 bytes.
Args check in FLASH_BANK_COMMAND_HANDLER():
first version of the driver had 7 args, current - 6. This patch will fix
error when flash is rejected (current k1921vk01t.cfg has flash bank init
with 6 args).
Timeouts in flash flag checking procedure:
increase timeouts in niietcm4_opstatus_check() and niietcm4_uopstatus_check()
cause there were problems in some hardware configurations.
JTAG ID:
wrong id in k1921vk01t.cfg replaced with right one.
Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru>
Change-Id: I84296ba3eb4eeda4d4a68b18c94666f1269a500f
Reviewed-on: http://openocd.zylin.com/3171
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch fixes the tap order so that it matches the actual jtag
chain when all taps are enabled. It also introduces a variable
DEFAULT_TAPS that can be set outside of this script, e.g. on the
command line, to specify which taps are to be enabled on init.
Lastly, a new debug target "am335x.m3" is added so that the Wakeup-M3
can be selected for debugging.
Change-Id: Iccf177fda8d5e3737b1b2bb8fd1eaa7d3262ed9f
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested with "J-Link OB RX621-ARM-SWD V1 compiled Nov 4 2014 10:47:22".
Change-Id: Ib64c0be407f99df57f058a4498556fd5ab7e9112
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3170
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested with Relax Kit for 5V Shields:
J-Link Lite-XMC4200 Rev.1 compiled Oct 14 2015 10:14:50
and with Relax Lite Kit:
J-Link Lite-XMC4200 Rev.1 compiled Oct 14 2015 10:14:50
Derived from xmc4800-relax.cfg.
Change-Id: I4e10fb6ed1f85168634d3b5259d3041ffc6b74d8
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3130
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tomas Vanek
Andreas Fritiofson
Harald Welte
Rick Foos
Vivien Didelot
Sean Cross
Antony Pavlov
Remco Bloemen
Uwe Bonnes
Matthias Welwarsky
Felix Held
Andreas Färber
Marc Schink
Samuel Martin
Ivan Meleca
Alexander Kurz
Freddie Chopin
Andrew Kohlsmith
Ivan De Cesaris
Tim 'mithro' Ansell
Manuel Limones
Bogdan Kolbov
Matthias Welwarsky