Update the board config for the DaVinci DM355 EVM so the reset-init
event handler does the rest of the work it should do:
- minor PLL setup bugfixes
- initialize the DDR2 controller
- probe both NAND banks
- initialize UART0
- enable the icache
git-svn-id: svn://svn.berlios.de/openocd/trunk@2699 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Prepare the DaVinci PLL code to support the version 0x0E module
used in newer chips (e.g. dm365): rename the original code so
it's specific to version 0x02 PLL modules, and update the dm355evm
code to use that new name.
Fix two minor bugs in that version 2 code: sysclk3 setup used
the sysclk2 divider address (affecting video processing on dm355,
no worry for now) and sysclk2 setup had a syntax error.
Also minor fixups to dm355evm, mostly to permit use of RTCK.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2447 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Move src/tcl to tcl/.
- Update top Makefile.am to use new path name.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1919 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Move src/target/{interface,target,board,test}/ into src/tcl/
- Remove existing rules in src/Makefile.am and src/target/Makefile.am.
- Add Makefile.am handling of *.cfg and *.tcl files in top Makefile.am:
- Add dist-hook to include such files under src/tcl in the distribution.
- Add install-data-hook to install contents of '$(top_srcdir)/src/tcl/'.
- Add uninstall-hook to remove the installed script files.
- Change paths to (un)install script files in '$(pkgdatadir)/scripts'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1918 b42882b7-edfa-0310-969c-e2dbd0fdcd60
NAND support for DaVinci-family drivers, with HW ECC support.
Declare the NAND chip on the DM355 EVM board.
Currently tested on DM355 for Linux interop using the standard
large page (2KB) chip in the EVM socket; "hwecc1" and "hwecc4"
work fine. (Using hwecc4 relies on patches that haven't quite
made it through the Linux-MTD bottlenecks yet.)
Not yet tested: 1-bit on small-page (although it's hard to see
how that could fail); 4-bit on small page (picky layout issues);
the "hwecc_infix" mode (primarily for older boot ROMs; testing
there is blocked on having new bootloader code).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1903 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Improve support for the DM355 EVM board, and eventually other boards based
on DaVinci chips:
- Provide generic "davinci.cfg" to hold utilities that can be reused by
different chips in this family. Start with PINMUX, PSC, and PLL setup.
- DM355 chip support updates: provide a dictionary with chip-specific
symbols, load those utilities.
- Create a new dm355evm board file, with a reset-init event handler
which uses those utilities to set up PLLs and clocks, configure the
pins, and improve the JTAG speed limit.
Also a minor tweak: provide a virtual address for the work area, matching
what the very latest kernels do. It's probably unwise to use OpenOCD while
the MMU is active though.
The DRAM isn't yet accessible, but NAND access is mostly ready.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1881 b42882b7-edfa-0310-969c-e2dbd0fdcd60
David Brownell
Øyvind Harboe
Zachary T Welch
dbrownell
oharboe
zwelch