OpenOCD cannot connect to BCM2711's JTAG interface on RPi 4B board until
the reset configuration mode is set as trst_only.
According to Table 94. GPIO Pins Alternative Function Assignment of
Broadcom's BCM2711 ARM Peripherals datasheet [1] and Raspberry Pi's GPIO
control in config.txt document [2], only Test Reset (TRST) pin (no
System Reset, SRST) is exposed.
[1] https://datasheets.raspberrypi.org/bcm2711/bcm2711-peripherals.pdf
[2] https://www.raspberrypi.org/documentation/configuration/config-txt/gpio.md
Change-Id: I806f0be9700fa0f0944b42c8a651a5731adc762b
Link: http://openocd.zylin.com/#/c/6364/1
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Reviewed-on: http://openocd.zylin.com/6367
Tested-by: jenkins
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds support for the Blinkinlabs JTAG Hat, a Raspberry Pi
expansion board that provides JTAG and SWD connections via level-
shifting buffers.
Change-Id: I228bf6a18890b7c3d6679bbc63bfe39f726d8323
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6372
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Drive the output enable for TMS and TDI
Change-Id: Ib23afd2f5149d4ce402d88781e68dcf0f074f395
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/4179
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The legacy ft2232 driver suggests that the adapter has tristate
buffers on both nSRST and nTRST, even though they were not used as
such.
Change-Id: I971692ea6b3439ac93311b89877825a5cc21df46
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3663
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Flyswatter URL is dead and requires us to use web.archive.org since
the product is discontinued. The Flyswatter 2 is still active and
accessible at a different URL.
Change-Id: Ib2d9de70a9728b0f0ef73f5e479bca81f958442c
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/6337
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add board configuration for Renesas Falcon board based on the R8A779A0 V3U SoC.
Change-Id: If8369f2e2b97dfea9ccbee2c9b916ef7094f9b92
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6315
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The V3U SoC is unique in that it now has 8x CA76 and CR52,
while the previous SoCs had CA57/CA53/CR7 . This can still
be handled without too complex modifications to the gen3
configuration file, so add the logic to handle it there.
Change-Id: I7ab33eacc1fd379d369988d3d6690d2e82346c7e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On SMP Renesas R-Car Gen2/Gen3 systems, select the boot core as
the default target using the 'targets' command. This way, the
user can start debugging code running on the boot core without
having to switch to the boot core by explicitly invoking 'targets'
command first, since it is likely the debugged code will run on
the boot core. Note that most of the code is already in place, it
was just not used, so this is more of a fix to make the original
intention work.
Change-Id: I727808adce617c1d9ebd6ffa34f60f5882cdae60
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6313
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Initial support for Renesas RZ/G2 MPU family
Change-Id: I5ca74cddfd0c105a5307de56c3ade7084f9c28d2
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
The Xilinx Zynq UltraScale+ SoC have an "AXI-AP" access port for direct memory accesses without halting CPUs.
Change-Id: I6303331c217795657575de4759444938e775dee1
Signed-off-by: Olivier DANET <odanet@caramail.com>
Reviewed-on: http://openocd.zylin.com/6263
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.
Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Fix manually the remaining lines that don't match simple patterns
and would require dedicated boring scripting.
Remove the 'expr' command where appropriate.
Change-Id: Ia75210c8447f88d38515addab4a836af9103096d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6161
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Enclose within double quote the argument of 'expr' when there is
the need to concatenate strings.
Change-Id: Ic0ea990ed37337a7e6c3a99670583685b570b8b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6160
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
In the TCL scripts distributed with OpenOCD there are 1700+ lines
that should be modified before switching to jimtcl 0.81.
Apply the script below on every script in tcl folder. It fixes
more than 92% of the lines
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
#!/usr/bin/perl -Wpi
my $re_sym = qr{[a-z_][a-z0-9_]*}i;
my $re_var = qr{(?:\$|\$::)$re_sym};
my $re_const = qr{0x[0-9a-f]+|[0-9]+|[0-9]*\.[0-9]*}i;
my $re_item = qr{(?:~\s*)?(?:$re_var|$re_const)};
my $re_op = qr{<<|>>|[+\-*/&|]};
my $re_expr = qr{(
(?:\(\s*(?:$re_item|(?-1))\s*\)|$re_item)
\s*$re_op\s*
(?:$re_item|(?-1)|\(\s*(?:$re_item|(?-1))\s*\))
)}x;
# [expr [dict get $regsC100 SYM] + HEXNUM]
s/\[expr (\[dict get $re_var $re_sym\s*\] \+ *$re_const)\]/\[expr \{$1\}\]/;
# [ expr (EXPR) ]
# [ expr EXPR ]
# note: $re_expr captures '$3'
s/\[(\s*expr\s*)\((\s*$re_expr\s*)\)(\s*)\]/\[$1\{$2\}$4\]/;
s/\[(\s*expr\s*)($re_expr)(\s*)\]/\[$1\{$2\}$4\]/;
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I0d6bddc6abf6dd29062f2b4e72b5a2b5080293b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6159
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This file has been added to OpenOCD 0.5.0 in 2011, before gerrit
gets in use, with commit ba71e8c521 ("at91: add chip register
definition and generic init support").
The only procedure in the file has never been referenced in any
other part of OpenOCD. This procedure has syntax errors while uses
its argument 'cs' and several unmatched parenthesis, which clearly
highlights that it has never been used so far.
Gerrit does not report any patch aimed at fixing it.
Even if the file seems unused and could be removed, let's fix it
in the hope it could get used.
While there, remove some useless parenthesis and format it using
the new simplified syntax required by jimtcl 0.81.
Change-Id: Ied26456262e7b99de37667a8ce418f4f12e237bd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ba71e8c521 ("at91: add chip register definition and generic init support")
Reviewed-on: http://openocd.zylin.com/6157
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Both http://openocd.zylin.com/542/ and http://openocd.zylin.com/543/
introduce the same typo in the bitfield for initializing the l2
cache of imx53.
One year later, http://openocd.zylin.com/1461/ copy-pastes the same
typo.
The comment above the code show that it's really an error and not
the expected behaviour.
Fix the typo replacing the incorrect comparison '<' with a left
shift.
Change-Id: I43725731a2228e28a676215f76936fa289d9395e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e3b3273433 ("cfg: add imx53loco board config")
Fixes: 108a458ab8 ("cfg: add icnova_imx53_sodimm board config")
Fixes: e608ced330 ("ftdi/board: Add support for DENX M53EVK")
Reviewed-on: http://openocd.zylin.com/6156
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Chip is similar to imx8x series but has different cores at different
addresses.
Support for reduced versions is not yet available.
Tested on imx8qm-mek board
Change-Id: Ia34a80d561ab2849a570d8c375b936a45cbf45ca
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-on: http://openocd.zylin.com/5042
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
All Altera USB Blaster devices require a dedicated line in the
udev rules, but some USB VID/PID present in interface and board
config file is missing in udev rules.
Add the missing Altera USB Blaster devices in udev rules.
While there, fix an incorrect pair VID/PID that are reported
swapped inside a comment.
Change-Id: I2d67e90b10db99ef2638405585859c1393456f65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6102
Tested-by: jenkins
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
The Broadcom BCM2711 used in Raspberry Pi 4
No documentation was found on Broadcom website
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711/
Change-Id: I3db6c9af520af8ab4c21ad35ff0f2db28efc0325
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6066
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Broadcom chip used in the Raspberry Pi 2 Model B
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2836
Change-Id: I50b040db213c5b72f63d5f5534c552426c7376f9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6068
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is the Broadcom chip used in the Raspberry Pi Model A, B, B+,
the Compute Module, and the Raspberry Pi Zero.
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2835
Change-Id: Ifeb012952473d624327e8c010ac5c886d9473aa0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6067
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Create the TPIU and SWO device in target config file.
Replace the target event 'trace-config' with the TPIU/SWO event
'post-enable'.
Extend the existing code in the event handler to properly set the
gpio mode and speed to permit synchronous trace.
This patch is not exhaustive of all the targets that have SWO, but
has to be considered as an initial example.
Change-Id: If4bbf364c0d2aef3ae49951e76507a3b1cfd58e7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5859
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Add board and target configuration files for
Ampere eMAG8180 board and Ampere eMAG processor.
Tested on an Ampere eMAG8180 development platform.
Change-Id: I222653f0fc12d25202a7e469db3594076cbc38ed
Signed-off-by: Anthony Ferranti <ferranti@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5569
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Ranjith Chandran
Marc Schink
Oleksij Rempel
Jian-Hong Pan
Matthew Mets
Patrick Stewart
Andreas Fritiofson
Florian Fainelli
Marek Vasut
Rohit Singh
micbis
Tarek BOCHKATI
Antonio Borneo
Olivier DANET
Peter Lawrence
Leonard Crestez
Andrew Wesie
Felipe Balbi
Jiri Kastner
Anthony Ferranti
Nishanth Menon