Specifically the Linux issue of needing "udev" rules, and MS-Windows
needing driver configuration.
Also, update the existing udev note to use the correct name of that
rules file in the source tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The recent patch to fixbreakpoints and dcache handling added
a bunch of overlong lines (80+ chars) ... shrink them, and do
the same to a few lines which were already overlong.
Also add a few FIXME comments to nudge (a) replacement of some
magic numbers with opcode macros, which will be much better at
showing what's actually going on, and (b) correct return codes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Get rid of new nasty warning:
NOTE! Severe performance degradation without fast memory access enabled...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix an unused variable warning seen when building the parport driver
under FreeBSD.
Using information from Xiaofan Chen <xiaofanc@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Breakpoints did not work because the data cache was not flushed
properly.
As a bonus add capability to write to memory marked as read only
by the MMU, which allows software breakpoints in such memory
regions.
For folk who don't know the ARM920 JTAG interface very well, the
two modes of scan chain 15 access to CP15 are confusing.
Make those parts of the ARM920 code less opaque, by:
- Adding comments referencing the relevant parts of the TRM,
catching up to similar updates in the User's Guide.
- Replacing magic numbers in physical access clients with
symbolic equivalents.
No functional change.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cortex-M targets don't support ARM instructions.
Leave the NVIC.VTOR setup alone, but comment how the whole
routine looks like one big bug...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
When a DSP563xx-aware GDB asks OpenOCD for target registers,
the result should be a GDB with register data ... not an
OpenOCD crash.
(Note that mainline GDB doesn't currently support this core,
so for now, this requires a GDB with FreeScale patches.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Removed remaining support for various commands, like advice for
migrating old-style TAP declarations.
The documentation no longer describes them either ... so if users have
been delaying config updates, they may need to consult older releases.
ALL this stuff has been clearly marked as "do not use" for at least a
year now, so anyone still using it hasn't been holding up their end.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Issue warning to user when unlocking or writing the option bytes.
The new settings will not take effect until a target reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Issue warning to user when unlocking or writing the option bytes.
The new settings will not take effect until a target reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This is a copy and paste of arm926ejs. Not tested, but
ready for testing at least. There is a good chance that
it will work if the generic armv4_5 fn's are robust enough...
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Copy of the 926ejs function. I have tested it only using
my rtems application (where virtual address mapping == physical).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Sometimes MS-Windows users try to use filesystem names which include
the "#" character. That's generally unwise, since it begins Tcl
comments.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
reset init would get stuck in an infinite loop when
e.g. khz was too high. Added timeout. This is a copy
of paste of a number of such bugfixes in the arm11
code.
Arm11 code reviewed for further such infinite loop bugs
and I couldn't find any more. Xing fingers it's the last
one...
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Not all cores and boards support adaptive clocking, so qualify
all advice to use it to depend on core and board support.
It's primarily ARM cores which support this; and many of the
newer ones (like Cortex-M series) don't.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The Doxygen output was previously titled "OpenOCD Reference Manual",
which was quite misleading ... the User's Guide is the reference
manual which folk should consult about how to use the software.
Just rename it to match how it's been discussed previously, and to
bring out its intended audience: developers of this software. As a
rule, Doxygen is only for folk who work with the code it documents.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Provide doxygen for many of the public ADIv5 interfaces (i.e. the ones
called from Cortex core support code).
Add FIXMEs (and a TODO) to help resolve implementation issues which
became more apparent when trying to document this code:
- Error-prone context-sensitivity (queued/nonqueued) in many procedures.
- Procedures that lie by ignoring errors and wrongly claiming success.
Also, there was no point in a return from dap_ap_select(); it can't fail,
and no caller checks its return status. Clean that up, make it void.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Init the ARMv7-M magic number. Define predicate verifying it.
Use it to resolve a lurking bug/FIXME: make sure the ARMv7-M
specific DAP ops reject non-ARMv7-M targets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Have the User's Guide and BUG handling notes both reference
the fact that we now have a bug database at SourceForge.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Segger publishes some documentation on this protocol;
reference it, so future maintainers can know it exists.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Moved board specific settings from target/at91r40008.cfg to a new
file board/ethernut3.cfg.
Set correct CPUTAPID. Reset delay increased, see MIC2775 data sheet.
Increased work area size from 16k to 128k.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove long-obsolete text about "erase_check" affecting "flash info" output.
Move parts of that text to "protect_check", where it's still relevant; and
update the "flash info" description to mention the issue.
(This is still awkward. It might be best to make "protect_check" mirror
"erase_check" by dumping what it finds, so "flash info" doesn't dump any
potentially-stale cache info.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For STR7x flash, the device cannot be queried for the protect status.
The solution is to remove the protection on reset init. The driver
also initialises the sector protect field to unprotected.
[dbrownell@users.sourceforge.net: line length shrinkage]
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The default state of the STR7 flash after a reset init is unlocked.
The information in the flash driver now reflects this.
The information about the lock status cannot be read from the
flash chip, so the user is informed that flash info might not
contain accurate information.
[dbrownell@users.sourceforge.net: line length shrinkage]
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The semihosting interface has a strange convention for read/write where
the unused amount of buffer must be returned. We failed to return the
total buffer size when the local read() call returned 0.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Test cases ran on v0.4.0-rc1 for a number of targets:
AT91FR40162
LPC2148
SAM7
STR710
STR912
The goal of the testing session was to prove basic functionality of OpenOCD for different targets.
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
srst_asserted and power_restore can now be overriden to do
nothing. By default they will "reset init" the targets and
halt gdb.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When the TAR cache was explicitly invalidated, don't bother
printing it; the actual hardware status is more informative.
Provide some doxygen for the MEM-AP setup routine.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Sometimes we saw two strange blank spaces at the beginning
of the telnet lines.
progress
ogress
>
This patch fixes this problem:
progress
progress
>
The code changes are *reasonably* clean, but perhaps it could be
made a bit more elegant, but I didn't want to change things after
I finished diagnosis/testing & submitting the patch.
The problem was that logging can send the text and the newline
separately in two different requests and the telnet code would
incorrectly remove the prompt from the end of a line.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
If the MEM-AP cache is invalid, don't display it; just report that
invalidity as an error. (This bug has been observed with "mdw 0 32"
after just a "reset halt". Some code is being wrongly bypassed...)
If it's valid, display that cache at DEBUG level, not ERROR. Also,
don't assume it's an AHB-AP; it could be another flavor of MEM-AP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Reject invalid AP numbers (256+) as Tcl operation parameters.
Shrink one of the overlong lines.
Add my copyright to the ADIv5 code (multiple contributions).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make messages reference "DAP" if they're actually transport-agnostic, or
"JTAG-DP" when they're JTAG-specific. Saying SWJ-DP is often wrong (on
most Cortex-A8 chips) and is confusing even if correct (since we don't
yet support SWD).
Rename a JTAG-specific routine to jtagdp_transaction_endcheck() to highlight
that it's JTAG-specific, and that identify DAP clients undesirably depending
on JTAG. (They will all need to change for SWD support.)
Shrink a few overlong lines of code. Copy a comment from code removed
in a previous patch (for the ARMv7-M "dap baseaddr" command).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make the ARMv7-M DAP code reuse the command handler for "dap baseaddr".
For some reason, this DAP command wasn't converted earlier.
This is a code shrink and simplification; it also removes a needless
transport dependency on JTAG.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Building with clang took a few very small changes. The change to
helper/log.h is because clang doesn't like an expression where the
result is unused. In helper/system.h, I just defined true and false
since clang doesn't have them builtin.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The "-f" is a shortcut for "-c" ... and providing any "-c" options
means the "openocd.cfg" file isn't implicitly used. Both the User's
Guide and the manual page were weak on these points, which has led
to some confusion.
Also update the manual page to include highlights of the search path
mechanism, including the facts that it exists and that "-s" adds to it.
Stop saying only the current directory is involved; the OpenOCD
script library is quite significant.
(Missing: complete manpage coverage of the search path, including a
FILES section listing all components and saying where the script
library is found.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell
Marc Pignat
Øyvind Harboe
Mathias Kuester
Spencer Oliver
Viktar Palstsiuk
Ethan Eade
Harald Kipp
Edgar Grimberg
Nicolas Pitre
Alex Austin